Terminale seriale nel browser: DiagROM Amiga e porta RS-232

SERIALE · RS-232 · DIAGROM · AMIGA · ANSISERIAL · RS-232 · DIAGROM · AMIGA · ANSI

Terminale seriale nel browser: DiagROM Amiga e porta RS-232Serial terminal in the browser: Amiga DiagROM and RS-232 port

Collega un adattatore USB-RS232 al computer e leggi qui, senza installare niente, quello che un apparecchio scrive sulla porta seriale. La modalità DiagROM è pensata per l'Amiga che non parte: imposta la porta, spiega in italiano i messaggi della ROM di diagnostica e ti fa scegliere le prove dal browser. Il terminale generico serve per tutto il resto. Non hai il cavo? C'è un Amiga simulato per provare.

Plug a USB-RS232 adapter into your computer and read here, with nothing to install, what a device writes on its serial port. DiagROM mode is made for the Amiga that will not start: it sets the port, explains the diagnostic ROM's messages and lets you pick the tests from the browser. The generic terminal is for everything else. No cable? There is a simulated Amiga to try it out.

⚡

La seriale dell'Amiga lavora a livelli RS-232, circa ±12 V. Usa un adattatore USB-RS232 vero, con il connettore a 9 poli. I moduli "TTL" a 3,3 o 5 V (quelli con i piedini, per Arduino) si rompono e comunque non leggono niente. Schema del cavo.

The Amiga serial port works at RS-232 levels, about ±12 V. Use a real USB-RS232 adapter with the 9-pin connector. The 3.3 V or 5 V "TTL" modules (the ones with pin headers, for Arduino) get damaged and cannot read anything anyway. Cable diagram.

TERMINALE SERIALESERIAL TERMINAL WEB SERIAL
Impostazioni della porta:Port settings: 9600 8N1
RX 0 · TX 0 byteClicca sul terminale per scrivere con la tastiera.Click the terminal to type with the keyboard.
Linee in uscitaOutput lines in entratainput CTSDSRDCDRI
COSA DICE DIAGROMWHAT DIAGROM SAYS
MENÙ DI DIAGROMDIAGROM MENU

Come si usa, in quattro passiHow to use it, in four steps

1 · Prepara l'Amiga1 · Prepare the Amiga

Monta la EPROM con DiagROM al posto del Kickstart e togli le espansioni. Come masterizzarla e montarla è spiegato in Amiga Doctor e in ROM e adattatori.

Fit the DiagROM EPROM in place of the Kickstart and remove expansions. Burning and fitting it is explained in Amiga Doctor and ROMs and adapters.

2 · Collega il cavo2 · Connect the cable

Tre fili tra la porta seriale dell'Amiga e l'adattatore USB-RS232, come nello schema. Collega tutto ad Amiga spento.

Three wires between the Amiga serial port and the USB-RS232 adapter, as in the diagram. Connect everything with the Amiga off.

3 · Premi Collega3 · Press Connect

Resta su "DiagROM Amiga" e "Porta seriale vera", premi Collega e scegli l'adattatore nell'elenco del browser. La porta è già a 9600 baud, 8N1, senza controllo di flusso.

Stay on "Amiga DiagROM" and "Real serial port", press Connect and pick the adapter in the browser's list. The port is already at 9600 baud, 8N1, no flow control.

4 · Accendi l'Amiga4 · Switch the Amiga on

Il testo compare subito, anche a schermo nero. A destra trovi le spiegazioni; quando DiagROM chiede un tasto la pagina risponde da sola e poi puoi scegliere le prove dal menù. Alla fine salva il registro.

Text appears at once, even with a black screen. Explanations are on the right; when DiagROM asks for a key the page answers by itself, then you can pick tests from the menu. At the end save the log.

Il cavo: tre fili incrociatiThe cable: three crossed wires

Servono un adattatore USB-RS232 con connettore a 9 poli (DB9 maschio) e un cavo null-modem, cioè con trasmissione e ricezione incrociate, che finisca con un DB25 femmina dal lato dell'Amiga (A500, A600, A1200, A2000, A3000, A4000). Si costruisce con tre fili: è lo stesso cavo descritto in Amiga Doctor.

You need a USB-RS232 adapter with a 9-pin connector (male DB9) and a null-modem cable, that is with transmit and receive crossed, ending in a female DB25 on the Amiga side (A500, A600, A1200, A2000, A3000, A4000). You can build it with three wires: it is the same cable described in Amiga Doctor.

DB25 femmina · lato AmigaFemale DB25 · Amiga side DB9 femmina · lato adattatore USB-RS232Female DB9 · USB-RS232 adapter side 2 TXD → 2 RXD l'Amiga trasmettethe Amiga transmits 3 RXD ← 3 TXD l'Amiga ricevethe Amiga receives 7 GND — 5 GND massaground NON collegareDo NOT connect 9 = +12 V 10 = −12 V 11 = uscita audio11 = audio out 18 = ingresso audio18 = audio in Niente cavi dritti a 25 fili.No straight 25-wire cables. Collega solo 2, 3 e 7.Connect only 2, 3 and 7. I numeri sono stampati sulla plasticaThe numbers are moulded into the plastic dei connettori: segui quelli, non laof the connectors: follow them, not the posizione nel disegno.position in the drawing.
Schema del cavo. Giallo: dati dall'Amiga al PC. Azzurro: dati dal PC all'Amiga. Verde: massa. In rosso i piedini con tensioni, in arancione l'audio.Cable diagram. Yellow: data from the Amiga to the PC. Cyan: data from the PC to the Amiga. Green: ground. Red pins carry voltages, orange ones audio.
Amiga, DB25Amiga, DB25SegnaleSignalAdattatore, DB9Adapter, DB9SegnaleSignal
2TXD, dati in uscitaTXD, data out2RXD, dati in entrataRXD, data in
3RXD, dati in entrataRXD, data in3TXD, dati in uscitaTXD, data out
7massa dei segnalisignal ground5massaground
  • Cavo già fatto: va bene un null-modem DB9 femmina – DB25 femmina. Controlla con il tester che 2 e 3 siano incrociati come nella tabella e che i piedini 9 e 10 del DB25 non siano collegati a niente. Un adattatore 9–25 poli "dritto" da solo non basta: non incrocia i dati.
  • Perché solo tre fili: DiagROM non usa il controllo di flusso, e sul connettore dell'Amiga ci sono anche +12 V, −12 V e l'audio. Il manuale hardware Commodore raccomanda di collegare solo i piedini che servono e di evitare i cavi a 25 fili tutti collegati.
  • Amiga 1000: ha un connettore femmina con una piedinatura diversa sui piedini non standard (−5 V sul 14, +5 V sul 21, +12 V sul 23, audio su 15 e 16, reset sul 25). I piedini 2, 3 e 7 sono gli stessi, ma serve un DB25 maschio.
  • Niente moduli TTL: la RS-232 usa tensioni positive e negative fino a ±12 V e ha la logica invertita rispetto alla seriale a 5 V di Arduino e simili.
  • Quale adattatore: quelli con chip FTDI o Prolific originali danno meno problemi di driver. Se sulla scatola c'è scritto "RS232" e ha il connettore a 9 poli con le due viti, è del tipo giusto.
  • Ready-made cable: a female DB9 – female DB25 null-modem is fine. Check with a meter that 2 and 3 are crossed as in the table and that DB25 pins 9 and 10 go nowhere. A "straight" 9-to-25 pin adapter alone is not enough: it does not cross the data lines.
  • Why only three wires: DiagROM uses no flow control, and the Amiga connector also carries +12 V, −12 V and audio. The Commodore hardware manual recommends connecting only the pins you need and avoiding fully wired 25-conductor cables.
  • Amiga 1000: it has a female connector with a different pinout on the non-standard pins (−5 V on 14, +5 V on 21, +12 V on 23, audio on 15 and 16, reset on 25). Pins 2, 3 and 7 are the same, but you need a male DB25.
  • No TTL modules: RS-232 uses positive and negative voltages up to ±12 V and its logic is inverted compared with the 5 V serial of Arduino and the like.
  • Which adapter: those with genuine FTDI or Prolific chips cause fewer driver problems. If the box says "RS232" and it has the 9-pin connector with two screws, it is the right kind.

Tutti i piedini della seriale dell'Amiga (A500, A2000, A3000)All pins of the Amiga serial port (A500, A2000, A3000)

PinSegnaleSignalVersoDirectionNoteNotes
1GNDmassa del telaio (schermo)frame ground (shield)
2TXDuscitaoutdati trasmessi dall'Amigadata sent by the Amiga
3RXDentrataindati ricevuti dall'Amigadata received by the Amiga
4RTSuscitaoutrichiesta di inviorequest to send
5CTSentratainpronto a ricevereclear to send
6DSRentratainapparecchio prontodata set ready
7GNDmassa dei segnalisignal ground
8CDentratainportante rilevatacarrier detect
9+12 Valimentazione: non collegarepower: do not connect
10−12 Valimentazione: non collegarepower: do not connect
11AUDOuscitaoutaudio del canale sinistroleft channel audio
18AUDIentratainaudio verso il canale destroaudio into the right channel
20DTRuscitaoutterminale prontodata terminal ready
22RIentratainsquilloring indicator

Gli altri piedini non sono collegati. Fonte: Amiga Hardware Reference Manual, appendice E.The other pins are not connected. Source: Amiga Hardware Reference Manual, appendix E.

Leggere DiagROM riga per rigaReading DiagROM line by line

DiagROM, di John "Chucky" Hertell, è una ROM gratuita che prende il posto del Kickstart e prova l'Amiga un pezzo alla volta. Scrive tutto anche sulla seriale a 9600 baud, 8 bit, nessuna parità, 1 bit di stop, senza controllo di flusso: per questo si riesce a lavorare anche con lo schermo nero. La versione stabile 2.0 è del 20 marzo 2026; le versioni di prova della 2.0 uscite tra maggio 2024 e luglio 2025 usavano 19200 baud.

All'avvio DiagROM non ha ancora memoria su cui contare, quindi procede a piccoli passi e li scrive nell'ordine della tabella. L'ultima riga che vedi dice dove si è fermata.

DiagROM, by John "Chucky" Hertell, is a free ROM that replaces the Kickstart and tests the Amiga one piece at a time. It also writes everything to the serial port at 9600 baud, 8 bits, no parity, 1 stop bit, no flow control: that is why you can work even with a black screen. Stable version 2.0 is dated 20 March 2026; the 2.0 test builds released between May 2024 and July 2025 used 19200 baud.

At start-up DiagROM has no memory to rely on yet, so it moves in small steps and writes them in the order of the table. The last line you see tells you where it stopped.

Cosa scrive (DiagROM 2.0)What it writes (DiagROM 2.0)Cosa vuol direWhat it means
DiagROM Amiga Diagnostic by John HertellLa CPU esegue la ROM e Paula trasmette. Se non arriva nemmeno questa riga: cavo, velocità, oppure l'Amiga non parte proprio (vedi Amiga Doctor).The CPU runs the ROM and Paula transmits. If not even this line arrives: cable, speed, or the Amiga does not start at all (see Amiga Doctor).
Checking status of mousebuttons at power-onElenca i pulsanti premuti all'accensione (P1LMB, P2RMB…). Se compaiono senza che tu prema niente, sono bloccati.Lists the buttons held at power-on (P1LMB, P2RMB…). If they show up while you press nothing, they are stuck.
Checking addressdata of ROM-SpaceRilegge la ROM a tratti: un punto è giusto, una E rossa è un tratto letto male.Reads the ROM back in chunks: a dot is correct, a red E is a misread chunk.
Checking if OVL works: OKLa CIA-A ha tolto la ROM dall'indirizzo 0. FAILED punta alla CIA-A o alla logica (Gary, Gayle).CIA-A has removed the ROM from address 0. FAILED points to CIA-A or the glue logic (Gary, Gayle).
Scan for usable Chipmem
Addr $00070000 OK, Number of working 64K blocks found: 8
Cerca la chip RAM a blocchi di 64 kB: 8 blocchi = 512 kB, 16 = 1 MB, 32 = 2 MB. È una ricerca, non una prova completa.Looks for chip RAM in 64 kB blocks: 8 blocks = 512 kB, 16 = 1 MB, 32 = 2 MB. It is a scan, not a full test.
Addr $00000000 ERROR (D31->D0): ------------X---------------X---Il blocco non tiene i dati. I 32 segni sono i bit da 31 (a sinistra) a 0 (a destra): X è un bit sbagliato. Sugli Amiga a 16 bit le due metà sono le stesse 16 linee dati: qui D3.The block does not hold data. The 32 marks are bits 31 (left) to 0 (right): X is a wrong bit. On 16-bit Amigas the two halves are the same 16 data lines: here D3.
Memblock found between: $… and $…La memoria buona finisce prima del previsto: da lì in poi qualcosa non risponde.Good memory ends earlier than expected: from there on something does not answer.
Doing addresstesting of area
OK memoryblock between: $… and $…
Scrive in ogni cella il suo indirizzo e rilegge: trova le linee di indirizzo in corto o interrotte. Con errori mostra una maschera A31–A0, che è solo una stima.Writes each cell's address into it and reads back: finds shorted or open address lines. On errors it shows an A31–A0 mask, which is only an estimate.
NO MEMORY FOUND SYSTEM HALTEDNessuna memoria utilizzabile: DiagROM si ferma qui e non risponde ai tasti.No usable memory: DiagROM stops here and does not answer keys.
Detecting agnuschip, working raster, Detected ChipmemTipo di Agnus (OCS, ECS o Alice AGA), contatore di riga e quantità di chip RAM.Agnus type (OCS, ECS or AGA Alice), line counter and amount of chip RAM.
Doing ROM Checksumtest, CPU: …, Checking for fastmemOtto somme di controllo della ROM (verde giusto, rosso sbagliato), processore e fast RAM non autoconfig.Eight ROM checksums (green right, red wrong), processor and non-autoconfig fast RAM.
To use serial communication please hold down ANY key nowVa premuto un tasto (o inviato un carattere) entro pochi secondi, altrimenti la seriale viene spenta. La pagina lo fa da sola.A key must be pressed (or a character sent) within a few seconds, or serial is turned off. This page does it by itself.
MAIN MENUAvvio finito: si scelgono le prove.Start-up finished: pick the tests.

I tasti del menù (DiagROM 2.0)Menu keys (DiagROM 2.0)

Ogni voce si sceglie con il tasto scritto alla sua sinistra, oppure con le frecce su e giù e Invio. I pulsanti del pannello "Menù di DiagROM" leggono le voci dallo schermo, quindi funzionano anche con la serie 1.x, che ha qualche voce diversa.

Each item is chosen with the key shown on its left, or with the up and down arrows and Enter. The buttons in the "DiagROM menu" panel read the items from the screen, so they also work with the 1.x series, which has a few different items.

TastoKeyMenù principaleMain menuCosa contieneWhat it holds
0SysteminfoCPU, chipset, memoria, registri dei chip customCPU, chipset, memory, custom chip registers
1Audiotestsforme d'onda sui quattro canali e modulo di provawaveforms on the four channels and a test module
2Memorytestschip RAM trovata (1), chip RAM estesa fino a 2 MB (2), fast RAM (3–5), ricerca completa (6), prova e modifica a mano (7, 8), autoconfig (9), menù (0)detected chip RAM (1), extended chip RAM up to 2 MB (2), fast RAM (3–5), full detection (6), manual test and edit (7, 8), autoconfig (9), menu (0)
3IRQ/CIA Testsinterruzioni (1, 4) e CIA (2, 3): timer, orologio TOD, allarme, richieste di interruzioneinterrupts (1, 4) and CIAs (2, 3): timers, TOD clock, alarm, interrupt requests
4Graphicstestsimmagini di prova: si vedono solo sullo schermo dell'Amigatest pictures: visible only on the Amiga screen
5Porttestsparallela (1), seriale (2), joystick e mouse (3). Parallela e seriale vogliono un connettore con ponticelliparallel (1), serial (2), joystick and mouse (3). Parallel and serial need a loopback plug
6Drivetestsfloppy (1), IDE di A600 e A1200 (2), IDE dell'A4000 (3)floppy (1), A600 and A1200 IDE (2), A4000 IDE (3)
7Keyboardtestscodici dei tasti premuticodes of the keys pressed
8Other testsorologio, autoconfig in dettaglio, lettura di un indirizzoclock, detailed autoconfig, reading an address
S, ASetup, Aboutnella 2.0 Setup torna al menù; About mostra le informazioniin 2.0 Setup returns to the menu; About shows the credits
SpazioSpacenel menù principale cambia il modo video (PAL/NTSC): non è scritto a schermoin the main menu it switches the video mode (PAL/NTSC): not shown on screen

Nei sottomenù 9 (o 0 nelle prove di memoria) torna al menù principale. Nelle prove un tasto qualsiasi o Esc ferma e torna indietro. La prova della porta seriale chiede di togliere il cavo e mettere un connettore con i ponticelli, quindi da qui non si può seguire.

Pulsanti all'accensione (dal testo "About" della 2.0): tasto sinistro del mouse nella porta 1 = schermo spento e uso della fast RAM se c'è; tasto destro = DiagROM lavora all'inizio del blocco di memoria invece che alla fine. Vanno rilasciati dopo poco, altrimenti vengono considerati bloccati e ignorati. Nella serie 1.x il fuoco del joystick spegneva la seriale: controlla le note della tua versione.

Trovato il guasto, passa a Amiga Doctor per i chip da controllare, a Pinout chip per i piedini di CIA 8520, DRAM e 68000 e all'Oscilloscopio per vedere clock, /RAS e /CAS.

In submenus 9 (or 0 in the memory tests) goes back to the main menu. During tests any key or Esc stops and goes back. The serial port test asks you to remove the cable and fit a loopback plug, so it cannot be followed from here.

Buttons at power-on (from the 2.0 "About" text): left mouse button in port 1 = screen off and fast RAM used if present; right button = DiagROM works at the start of the memory block instead of the end. Release them shortly after, or they are treated as stuck and ignored. In the 1.x series the joystick fire button turned serial off: check the notes of your version.

Once you have found the fault, move on to Amiga Doctor for the chips to check, Chip pinouts for the 8520 CIA, DRAM and 68000 pins, and the Oscilloscope to look at clocks, /RAS and /CAS.

Il terminale genericoThe generic terminal

Scegli "Terminale generico" per parlare con qualsiasi cosa abbia una seriale: un modem, un vecchio terminale, la console di un router, una scheda con Arduino o ESP32, uno strumento da laboratorio. Qui sì che servono i moduli TTL a 3,3 o 5 V, se l'apparecchio lavora a quei livelli: l'importante è che adattatore e apparecchio parlino la stessa tensione.

  • Velocità: deve essere uguale dalle due parti. Se non la conosci prova 9600, poi 115200, 19200, 38400 e 57600. "Altro" accetta qualsiasi valore; 31250 è la velocità del MIDI.
  • Bit di dati, parità, stop: quasi sempre 8, nessuna, 1 (scritto 8N1). I sistemi più vecchi usano a volte 7E1.
  • Controllo di flusso: "hardware" usa RTS e CTS e serve solo se il cavo li collega.
  • Invio: una riga di testo con il fine riga che scegli (CR, LF, CR+LF o niente), oppure byte in esadecimale come 1B 5B 41. Con il terminale selezionato ogni tasto parte subito.
  • Eco locale: mostra anche quello che scrivi, se l'apparecchio non lo rimanda indietro.
  • Vista esadecimale: ogni byte ricevuto (RX) e inviato (TX) con orario e posizione. Utile con i protocolli binari.
  • DTR e RTS: si accendono e spengono a mano. Su molte schede Arduino un impulso su DTR fa ripartire il programma. CTS, DSR, DCD e RI mostrano le linee in entrata, se l'adattatore le riporta.
  • Colori e cursore: il terminale capisce i codici ANSI/VT100 (colori, posizione del cursore, pulizia di schermo e riga). Lo schermo è di 80 colonne per 33 righe; le righe uscite dall'alto restano sopra.
  • Registro: "Salva registro" scarica un file di testo con l'orario di ogni riga ricevuta e inviata. Dalla vista esadecimale salva i byte. I dati restano nel tuo browser: questa pagina non manda niente a nessun server.

Choose "Generic terminal" to talk to anything with a serial port: a modem, an old terminal, a router console, an Arduino or ESP32 board, a lab instrument. Here the 3.3 V or 5 V TTL modules are the right tool, if the device works at those levels: what matters is that adapter and device use the same voltage.

  • Speed: it must match on both sides. If you do not know it try 9600, then 115200, 19200, 38400 and 57600. "Other" accepts any value; 31250 is the MIDI speed.
  • Data bits, parity, stop: nearly always 8, none, 1 (written 8N1). Older systems sometimes use 7E1.
  • Flow control: "hardware" uses RTS and CTS and only helps if the cable connects them.
  • Sending: a line of text with the line ending you choose (CR, LF, CR+LF or none), or hex bytes such as 1B 5B 41. With the terminal selected every key is sent at once.
  • Local echo: also shows what you type, if the device does not send it back.
  • Hex view: every byte received (RX) and sent (TX) with time and offset. Useful with binary protocols.
  • DTR and RTS: switched by hand. On many Arduino boards a pulse on DTR restarts the program. CTS, DSR, DCD and RI show the input lines, if the adapter reports them.
  • Colours and cursor: the terminal understands ANSI/VT100 codes (colours, cursor position, screen and line clearing). The screen is 80 columns by 33 rows; rows that scroll off the top stay above.
  • Log: "Save log" downloads a text file with the time of each line received and sent. From the hex view it saves the bytes. Data stays in your browser: this page sends nothing to any server.

Se non funzionaTroubleshooting

Cosa succedeWhat happensCosa controllareWhat to check
Nell'elenco del browser non c'è nessuna portaThe browser's list shows no portAdattatore collegato? Su Windows guarda in Gestione dispositivi se compare una porta COM: se c'è un punto esclamativo mancano i driver (CH340, Prolific). Su Linux l'utente deve stare nel gruppo dialout (o uucp).Adapter plugged in? On Windows look in Device Manager for a COM port: an exclamation mark means missing drivers (CH340, Prolific). On Linux the user must be in the dialout (or uucp) group.
"Non riesco ad aprire la porta""Cannot open the port"La porta è in uso da un altro programma (PuTTY, Tera Term, Arduino IDE) o da un'altra scheda del browser: chiudilo e riprova.The port is in use by another program (PuTTY, Tera Term, Arduino IDE) or another browser tab: close it and retry.
Non arriva nienteNothing arrivesTXD e RXD non incrociati, massa non collegata, Amiga spento. Su un Amiga con DiagROM: se lo schermo cambia colore ma qui non arriva niente, sospetta i driver 1488/1489 della seriale o Paula.TXD and RXD not crossed, ground not connected, Amiga off. On an Amiga with DiagROM: if the screen changes colour but nothing arrives here, suspect the 1488/1489 serial drivers or Paula.
Arrivano caratteri senza sensoGarbage characters arriveVelocità sbagliata (per DiagROM prova 19200), bit di dati o parità sbagliati, adattatore TTL su una porta RS-232. DiagROM 1.x manda apposta 12 byte strani prima del testo.Wrong speed (for DiagROM try 19200), wrong data bits or parity, TTL adapter on an RS-232 port. DiagROM 1.x deliberately sends 12 odd bytes before the text.
DiagROM scrive ma non risponde ai tastiDiagROM writes but does not answer keysIl filo dal piedino 3 del DB9 al piedino 3 dell'Amiga, oppure la seriale è stata spenta perché non è arrivato un tasto in tempo: riavvia l'Amiga lasciando attiva la risposta automatica.The wire from DB9 pin 3 to Amiga pin 3, or serial was turned off because no key arrived in time: restart the Amiga leaving the automatic answer on.
Il testo si ferma a metàThe text stops halfwayÈ il punto in cui DiagROM si è bloccata: leggi l'ultima riga e la sua spiegazione, poi salva il registro.That is where DiagROM hung: read the last line and its explanation, then save the log.

Fonti e limitiSources and limits

  • DiagROM: velocità, formato, testi dei messaggi, ordine dell'avvio e tasti del menù vengono dal sorgente ufficiale della versione 2.0 (github.com/ChuckyGang/DiagROMV2) e della 1.2.1 (github.com/ChuckyGang/DiagROM), e dalle note sul sito diagrom.com. Il sito non ha un manuale dei messaggi: le spiegazioni in italiano sono nostre e seguono quello che fa il codice.
  • Piedinatura della seriale: Amiga Hardware Reference Manual, appendice E.
  • L'Amiga simulato ripete i testi e l'ordine della versione 2.0, ma indirizzi, checksum e quantità sono d'esempio e le prove dei sottomenù non sono riprodotte.
  • Chip da sostituire: la pagina indica le linee dati o di indirizzo che sbagliano, non la sigla dell'integrato sulla scheda, che cambia con modello e revisione.
  • Non provato su hardware: la pagina è stata collaudata con l'Amiga simulato. Se la usi con un Amiga vero e qualcosa non torna, scrivici.
  • DiagROM: speed, format, message texts, start-up order and menu keys come from the official source of version 2.0 (github.com/ChuckyGang/DiagROMV2) and 1.2.1 (github.com/ChuckyGang/DiagROM), and from the notes on diagrom.com. The site has no manual of the messages: the explanations are ours and follow what the code does.
  • Serial pinout: Amiga Hardware Reference Manual, appendix E.
  • The simulated Amiga repeats the texts and order of version 2.0, but addresses, checksums and amounts are examples and the submenu tests are not reproduced.
  • Chips to replace: the page names the failing data or address lines, not the chip designator on the board, which changes with model and revision.
  • Not tested on hardware: the page was tested with the simulated Amiga. If you use it with a real Amiga and something looks wrong, write to us.

DiagROM è di John "Chucky" Hertell. Amiga è un marchio dei rispettivi proprietari. Questa pagina non è collegata al progetto DiagROM.DiagROM is by John "Chucky" Hertell. Amiga is a trademark of its respective owners. This page is not affiliated with the DiagROM project.

Views: 23